Jamstix & REAPER

stpete111 · Post by **stpete111** » Fri Feb 07, 2014 3:58 pm

Hi, just installed JS3 on this pc for the first time - opening Reaper 4.25 it crashes while scanning the JS3.dll, and therefore can't start it. This is Jamstix 3.5 on Win7 SP1. - 64 bit plug in in 64 bit Reaper.

The exact error message says:

"Plug-in 'jamstix3.dll' executed invalid operation during scanning,
Note if Reaper crashes as a result of this, simply run it again and it will continue on the next plug-in"

Any ideas on this one? Thanks.

Post by **Ralph @ Rayzoon** » Fri Feb 07, 2014 5:15 pm

Make sure the license key file is in the main Jamstix folder. If that is the case, send me rzdlog.txt from Documents\jamstix3.

stpete111 · Post by **stpete111** » Mon Feb 10, 2014 9:35 am

Ralph [RZ] wrote:Make sure the license key file is in the main Jamstix folder. If that is the case, send me rzdlog.txt from Documents\jamstix3.

Ralph, well that explains it. The license key was in the right folder, but when I went to get you the rzdlog file, there was no Jamstix folder in my Documents folder! Reason being, I installed Jamstix under the Administrator account but was trying to use it under my main user account. I copied the Jamstix folder from Admin's Documents folder to mine, and all is good now.

Thanks.

babacane_A · Post by **babacane_A** » Fri Jul 04, 2014 2:16 pm

Hi,

As many, I have just installed JS 3.6: Actually, I cannot use it anymore in Reaper. I have CPU peak (100%!) which are totally abnormal. With the old 3.5, JS was currently using 3 or 4% of my CPU. It seems there is something wrong with the new update in Reaper.

Thanks in advance for a possible solution.

Ciao

Post by **Ralph @ Rayzoon** » Sat Jul 05, 2014 9:52 am

That's not normal, please email me Documents\Jamstix3\rzdlog.txt and apslog.txt. Thanks!

babacane_A · Post by **babacane_A** » Sat Jul 05, 2014 11:05 am

Thanks Ralph!

I have just sent the 2 files to support@rayzoon.com. I hope this is the right email address!

Ciao!

babacane_A · Post by **babacane_A** » Sat Jul 05, 2014 12:06 pm

Hi Ralph,

Thanks a lot for your answer. I have read you were very helpful. This is true!

It seems everything is resolved... I will however run some test.

Thanks again!

fab_Z · Post by **fab_Z** » Fri Jul 25, 2014 1:00 pm

Hello,

I have a problem with Jamstix 3.6. I am running Jamstix 3.6 on Windows 7 32-bit with Reaper 4.62. When I start a project there occur dropouts and crackles. The CPU-load increases up to 30-40 % in small projects and up to 100 % in bigger projects. If I mute Jamstix then the problem does not occur. The problem exists since I upgraded to Jamstix 3.6. It would be great if someone could help me with this. I can not work with the current release of Jamstix at the moment. In addition I have the impression that moving the interface of Jamstix on the screen increases the CPU load significantly.

Post by **Ralph @ Rayzoon** » Sat Jul 26, 2014 3:53 pm

fab_z: please open Documents\Jamstix3\jamstix3.ini in NOTEPAD and add this line after [GENERAL]:

PriorityMode=1

If this does not help, please email me these files from Documents\jamstix3:

-apslog.txt
- rzdlog.txt

fab_Z · Post by **fab_Z** » Mon Jul 28, 2014 3:36 am

Hello Ralph,

thanks, this helped a lot. Now it works.